Search results

I just set up my late grandfather's Winchester M88 for this fall, but I used a 165 HotCor. I found boat tails would not shoot out of it so I tried the HC and it was amazing. The old girl will hit 2740 fps and is under an inch with 48.5gr of 2000MR. Seated at 2.820ish. Bit heavier than you...

24 Nosler eh? I guess we can expect the announcement before 3-4 months is up? Sent from my SM-G960U using Tapatalk

I was .010" longer than their recommended COAL, so extremely close, was about .078" short of the lands. When I switched to H1000, two three shot groups gave the same results, one at about 1oclock, next two over an inch away touching at the 11. Shot the same target, same results 15 minutes...

Just to close the loop, I'm giving up on these bullets. I tried different seating, different powder charges, I cleaned the barrel, switched to H1000, nothing under 1.25". I switch to the 180 ELD-M in a middling load of H1000 and consistently get .25moa groups. I can decide today what I'm...

I've been testing the classic 38.0gr H380 the past few weeks, using 52gr Nosler CC and 53gr Vmax. With the Vmax I got four in one hole and a 5th less than 1/2" away using WLRM primers. Non-magnum gave a bit larger group. I tried sweating depth and CCI200, WLR and WLRM with the 52 CC, all under...

I loaded up cfe223, tac and h322 this morning to see what will work best. Something will tickle his fancy I'm sure. Sent from my SM-G960U using Tapatalk

What are you using for a load of AA2200? Sent from my SM-G960U using Tapatalk

I struggled but didn't pull the trigger. Probably should get some more 95gr BTs but just ordered 500 165 308 HotCors. My wife said I have too many bullets. I did an inventory and realized I have just about enough for this month. ;) Sent from my SM-G960U using Tapatalk

What's everyone using in their 204's? I'm loading for my FIL's No1, I believe it's a shorter barrel, I've only shot it a few times. I have 32/34 grain bullets on hand, he liked 25.0gr Rx10 with the Varmint Nightmares, but it didn't have as much velocity but drop as 32gr vmax and 28.0gr H335...

Did you put that load on a chrono? Vertical stringing is usually more to do with large es, while horizontal is generally the rifle. If the es is good then start seating out by 0.030" at a time, should see something tighten up. How far out can you seat in that mag? Sent from my SM-G960U using...

Deer will be my late grandfather's Winchester M88 I was given for Christmas this year with a 165gr HotCor. If I get pulled for a moose permit I'll probably go with my 338-06 with either 200gr NBT or 225 Accubond. If I don't get the call for a moose, I might get to go out west for a hunt of a...

https://www.midsouthshooterssupply.com/ ... other+Shot! No more guessing eh? Sent from my SM-G960U using Tapatalk

For 150gr Swift Scirocco II's, I use standard H4831, 67.0 gr with F215 primers and a good jump. I'd start around 63gr, go up by .5gr with only one round and chrono them. Once you get around your desired velocity, do a .2gr flat spot test starting 1 grain below and .6-1 grain above your desired...

I went out and tested 64.3, two three shot groups at 100 yards netted about 1.25", sp I think with the bullet seated in a little further I can tighten it up. Going to swy away .075" and .100", do a three shot group and see what happens next. Hard to find the time right now. I'll get the info...

If you have a well, have the water tested and you will see that there are trace amounts of lead in the water. That's something you use everyday. That being said, I completely understand how you feel, and if you think the concern will take away from your hunting experience then do the change and...

I think I'm going to use some H1000 and see how it works with my gun and bullets to see if it's just a faster set up or I'm flirting with pressures. See how close I can come to Federal's data. Sent from my XT1650 using Tapatalk

I apologize, 7mm Rem Mag, 160gr TBT Sent from my XT1650 using Tapatalk

Has anyone loaded these yet? I just did a quick work up to try and get some data before I start accuracy testing. I started with 64.0 gr RL23 and went up to 65.2 and stopping, all in .2gr increments. Data is as follows: 64.0 - 3110 64.2 - 3099 64.4 - 3100 64.6 - 3123 64.8 - 3116 65.0 - 3121...

What are you using for a load with those suckers? Sent from my XT1650 using Tapatalk

Haha well do a Google search for the 338 Sherman then, tell me what you think then. I think whatever you go with you'll like it. Keep us posted which route you go! Sent from my XT1650 using Tapatalk