Search results

Making the brass from 06 is doable, but you have to turn the necks since on 22-250 brass you are making the neck out of the brass body of the 06 and making the neck thick. That's one potential problem that would lead to high pressure, difficulty chambering and inconsistent performance. If a lot...

Interesting as Switzerland as of today will not sell arms etc to the US over Middle East military involvement. Reminder 17 is a great powder for most medium and large cases.

Did that near Mendocino. Little blacktail ran off onto private property complete with mixed raspberry and poison oak. Round nose at 2400 fps in 25-06 after that.

If you want to experiment with subsonic, Titegroup and Trail boss work well per the Hodgdon website.

Just finding interesting brass at the range can be a catalyst

Goofing around We have some 115 grain Speer 7mm hollowpoint bulllets. We have a 7 mm PRC. Is the combo a bad idea? Any load data out there?

Yup, lb of titegroup for$32 including tax

I loaded a few 168 BT's and 180 Accubonds to shoot to check velocities and accuracy etc.

My grandad used a wad of graphite over his powder in 22-250 with home made bullets.

My Montana homesteader Grandpa made his from sawmill blades. We still have a butcher, a skinner and a cleaver of his. They hold an edge better when cutting up elk deer and lamb than our high end Henckel or Solingen knives. Owning something made by a family member is the best! Perhaps something...

If you live near one of the training areas you can try it out. They rent or lend the rifles and skis and give classes. One of my friends who was a downhill instructor found out she was good at it late in life even tho she hadn’t fired a gun before. They fire 22 shorts...

https://forum.castbulletassoc.org/thread/1387-the-load-is-13-grains-of-red-dot/ more rifle data for various calibers

Rifle cartridges with CAST LEAD bullets. I use it (and green dot) in 308, 30-06, 375 ruger for low velocity loads with non gas checked bullets. Cowboy data http://www.gmdr.com/lever/lowveldata.htm

Scheels in Sparks has primers as little as 49 per k. Bi mart in Deer Park, Cheney etc also has CCI primers at 49/K. The General Store in Spokane has reloading components on sale. North40 in various NW towns. Spokane etc has powder on sale. Example Staball 6.5 for $40. IMR powders about $50

I couldn't find they were still in business as I needed a new screen. Ended up using one of those Chinese hot plastic staplers to repair the the screens and as a bonus they are one piece now and are easier to install.

https://thetacticalprofessor.net/wp-content/uploads/2025/02/shootists-challenge-final.pdf A stamp for the center square, an old 1 cent Ben Franklin. I have some of those stamps.

"You do not want your first experience to end with tracking a wounded elk, or worse, losing that animal." My experiences bow hunting. The black bears were living high on the "hog".

Have a super lightweight 308 with a 2-7 power scope I have been using for mule deer in steep mountains. Best bullet so far accuracy wise is a 178 ELD X at 2550 fps. Would like to us the rifle for elk in the steep and wondering which bullet I have on hand to use. Distance is limited by the...

So am considering getting some seconds from Midway that appear from purchasers comments to be the Hornady ELD X but with a flat poly point instead of a sharp one. Would mostly be using them for target. Just wondering how to figure the change in BC versus the first quality items and if it is...

Will they be selling a. barrel with each 500 rounds. I had a little Yamaha RD 250 back in the day. Racers would outdo the 750's with them. But they rebuilt the engine for each race.