Search results

if I was going to get into the cell cameras , I'd take a look at the Cuddie back system that has a master camera and the other cameras link to the master camera . I think you can link up to ten cameras . this system uses one phone plan . I haven't researched it , only what I kind of remember...

very nice , you're a lucky Pappy

I've never tried to test warm ammo shot in cold temps . I don't know how I could have repeatable conditions . I have tested cold , and very cold temps with my labradar . I put everything in the truck and let the truck set out over night . go to our range set up and shoot . I needed to do...

I did goof in my previous reply . I'll edit it now . yesterday I wrote I like to work in the 100 - 105% case fill , that is wrong . I like to be in the 95% - 105% . I like to work in the 95% - 105% case fill . I'll work a little over 105% , and I'll work a little under 95% , but I try to...

I have no problem loading the full 60% reduction . if I were you , I'd round the 23.7 grain off to 24.0 and start loading . watch for low PSI signs . usually it's hangfire , and primers backing out , smoke back the brass case body . I have not seen these while using H4895 . I've used...

you are seeing the same thing I am . I don't need to adjust my die , to keep contact between the die and shellholder regardless of what shellholder in the set I'm using .

yes that case fill % is safe . I like to work in the 95% - 105% case fill range , at max load . what you are seeing is , this powder is a little slow for this combo . you are going to see a higher case fill , and a lower velocity . this powder maxes out at 50.1 grain 110.7% case fill ...

this is what I use . I run it with a cordless drill . I've done 222 rem to 338 Lapua , 41 rem mag , 45 acp https://www.midwayusa.com/product/1012881432?pid=720825 the trimmer you have pictured , I don't think you need anything else to go along with it . the problem I see with it is ...

I've never ran into this . I think the difference must be in the height of the slot .

I brought a couple home that you couldn't cut the gravy with a fork .

when I was hunting them , I skinned them and baked them in an oven bag . they really didn't go over well at a family meal . I haven't hunted them for a long time . I'm not sure if I'll hunt them this year .

here is a write up on a reduced load I did for my grandson's 260 Rem . maybe there is something in there that will help you . https://forum.nosler.com/threads/reduced-recoil-load.42158/

yes , I use them for everything . I have four sets of them . they are great . I have three different 7mm-08's and one set of dies . I just use the appropriate shellholder . I could never get a consistent shoulder bump by gapping the die away from the shellholder . using these shellholders my...

start low and work up while watching for pressure is the golden rule that should always be followed . if starting out at close to a max load , what do you do when you lock the gun up ? or how much do you lower the charge to get a safe load ? this is a method for disaster .

off the top of my head , my 7mm rem mag in a MKv weatherby , and my 7mm-08 Tikka 595 . both of these reach the lands and feed from the magazine . edit to add ; with the bullets I'm shooting out of them . 160 accubond in the 7 rem mag , Hornady 139 BTSP in the 7mm-08 . I'm can see some of...

I used to shoot a few indoor pistol leagues through the winter . these clubs all had bullet traps . I helped to clean out my local club trap . all it was , is a heavy piece of steel , probably 1/4" , placed in at an angle . the top of the steel towards the shooters . I'm not sure of the...

the hyper link is right here ,when I mouse over it , it shows up as a red line on this quote.................................................................................................................................XXXXXXXX

yes , I can reach the lands in a few of my factory rifles .

another very faint hyperlink in the post above .

there is a very faint hyperlink in the post above . looks to be another scammer .