Search results

After I took it apart and cleaned it I did not notice anything out of place. But now with an empty mag pull back the slide and it is very hard to release cannot do it with my thumb holding the gun but if you put a loaded mag in it its easy and smooth as silk. Also when you get to the last shot...

Hello, I recently purchased a Sig 1911 10MM. I have shot only 10 rounds through it and now the slide release is super stiff. Were before I shot it I could release it with my thumb pretty easily. I took it apart and cleaned it out. My question is will it loosen up the more I shoot it or will...

Thanks guys for replying. I checked the length and my loads were at 3.690 and I seated them down to 3.60 and loaded up a few and with give it a try. I am also dusting off my chrono and see what the speed is. my load with 140 ttsx are 3350 so I am curious to see the speed of the 160's I...

Hello guys, I have a great load using 140 TTSX and IMR7828ssc but wanted to try shooting some 160's accubonds. I started at 72 grains of IMR7828ssc and worked up to 76 grains shooting three shot groups moving up 1 grain at a time. I was shooting off a magnum gun rest at 100 yards. 71 to 74...

Went to Canada to catch some Channel Catfish. My son and I caught 58 cats in 2 days with 4 under 20 lbs and 6 over 30lbs and 48 between 20 to 30 lbs. I would recommend this trip to everyone! LT

Thanks for all the responses. I will be putting my leupold scope on it and I have H110 and 210 XTP bullets so I should be in great shape. Thanks again LT

Hello, I just picked up a 41 rem mag. Always wanted one never shot one. I was hoping I could get a little info from someone willing to share there experiences on some hand loads for this caliber. I have lots of different powders on hand and was thinking of starting with H110. thanks in...

Positive on the load of 76 grains of IMR4350. I am at the lake home but will post the OAL tomorrow when I get home Like any load all guns are different I recommend starting low and working your way up I did try H4350 in the same load but not as accurate LT

I do all my fly tying and hand loading in the winter when I have down time. build up the stock and your good to go for the spring, summer, and fall activities. Even bought a Dillon press for the hand guns. LT

This is my go to load for the .375 H&H 3 shot group. Hope this helps you. One thing I have found using this load is I can change between 270 or 300 grain bullets and both are extremely accurate. I am shooting a Browning .375 H&H gold medallion' LT

They shoot great out of my .375 H&H. I am using 76 grains and a 300 accubond.

Anybody shooting 110 grain bullets out of a .270 winchester. I picked up a sample pack that other day of 110 grain bullets and thought what the heck might be fun to see how fast I can push them and will they group. Anybody ever play with them. thanks LT

My go to load is a 76 grains of IMR4350 pushing a 300 accubond 3 shot group is .6 can't go wrong. LT

Does anyone use one of these? I just purchased one in 40 caliber. i go though a lot of 40 cal and the old Rock chucker just takes to much time to load 100. Any thoughts or suggestions on one if you own one? thanks LT

I use wipe out foam and it does a amazing job on copper. I usually clean my barrels after each range trip my worst fouler is my 30-378 bee the patches come out deep purple. Lt

I bet you could hit 3K. I have a 24 inch barrel and I can hit 3k with 150 grain partitions out of my .270 win. LT

I got a big gun safe from costco for 799.00 and they dropped it off free and left it in the garage. Only problem was a 64 gun safe in garage. I then hired a piano mover and 3 guys got it in the house, up the flight of stairs and in the spare room in 15 min for 300 bucks. Best 300 I ever...

I agree the accubonds seem to be a little more accurate but I did a little test shooting into reams of new printer paper I lined up a new box of it and shot into it at 100 yards. The accubond pretty much got destroyed and weight retention was 68% but was flat as a pancake. The interbond...

I have bought a couple of used guns from people I know that swear the barrel is history. I had one gun it took me a week of using wipeout over night and now the gun shoots lights out. I would agree with the rest of the folks who say get rid of the bronze brush. I haven't used them in years...

I have a Browning gold medallion .375 H&H and it just loves IMR4350 76 grains pushing a 300 grain accubond. You can't go wrong with this load!