Ruger No 1

Vince

Handloader
May 26, 2012
4,874
1,646
I picked up a Ruger No. 1 in .416 Remington Magnum earlier this year.

My next African hunt will be for Cape Buffalo using said No. 1. I discovered that I really liked stalking close, bow hunting close, and got within 5 Yards of a Nyala cow when my PH and I were sneaking through the brush looking for a Nyala bull. I shot my bull at ten yards with a .300 Win Mag.

I used to shoot further but now that I’m older I like the challenge of stalking close if the conditions are right. Anyway I still shoot further at the range as it makes the close shots easier.

So my long winded way to my question is, has anyone used a Hick’s Accurizer on a Ruger No. 1? I may have to take a far shot now and then and want the most accurate No. 1 I can get.

I’m thinking, cut the stock to fit me, put a mercury recoil reducer in the stock, add a grind to fit Limbsaver recoil pad, and maybe some lead weight in the fore end as well. I’m thinking a ten to eleven pound rifle would be about right given the amount of recoil. The terrain is flat and I don’t plan on packing it up and down mountains. I also don’t care about collector value. It’s mine and I’m going to make it fit me.

Vince
 
Vince I’ve installed a Hicks on most of my number 1s, it is straight forward process and helps to stabilize the front end should free floating become a solution. Used a router, not advised, a dremmel, better than a router and a milling bit on a drill press -the best way to remove the wood necessary to install the HIcks. Typically the heavy barreled rifles, don’t need it or benefit from it much. I have bedded the HIcks into the foreend. They say it’s not necessary but I think it’s a mistake not to.
Here is how to tell if your rifle will benefit, simple dry fire drill. From the bench support the fore end of the rifle back near the receiver. Sight in on a 100 yard target, using as perfect technique as you can dry fire. If the cross hair appeared to jump an inch or so on the target the hicks will help with overall accuracy. The jump is caused by the spring hanger in the fore end, the Hicks stabilizes it.
Regardless of adding and bedding the Hicks I’ve never seen a #1 in any caliber that would not benefit from bedding the fore end to the receiver and bedding the end of the spring hanger in the fore end. Two piece stocks on any rifle lead to consistent accuracy issues bedding helps to resolve those issues.
Most articles suggest free floating the fore end. I’ve started full length bedding a couple of them. This effort is best considered a case by case solution.
I think adding weight to the fore end could really mess things up. Don’t do that, plus you have very little wood to work with and you don’t want to weaken the fore end.
Trigger replacement, I’ve done four. If I do five I’ll send it off to get done. There is one of the three pins you have to remove that is a real PIA. With a proper press no big deal.
I would suggest having a competent smith add a brake to your rifle. You may need a new barrel band for the front sight but I think that a better solution then a weakening the butt stock.

Wouldn’t do any of it until I shot the rifle.

The good thing about the 416 is none of them were produced until after Ruger started making their own barrels. Yours may prove perfectly adequate.
I am always amused when I talk to guys who have pillar bedded their bolt action guns, added aftermarket triggers, bedded the scope bases replaced the extractor who think #1s are cool rifles but they don’t want to mess with them.
 
Most of what I’ve learned, including full length bedding the fore end was from Paul Hampton, a very talented gun smith who recognized how few good #1 smiths are available. He has only been specializing a few years but is booked so far out right now he may not be taking any more work for a bit. If any one needs a number one smith let me know I’ll get you his information.
 
I own three #1s but am not comfortable trying to accurize them myself. I need to find a good Smith to complete the task.
 
Countrycustommetalsmith. Fallon Nevada. Paul Hampton is your guy. He has done a couple for me and hopefully do my 257roberts to 257AI re-barrel. If you look at his web site the 300HH with custom rib I’m guessing is mine. :)
 
Last edited:
Vince
I would be leary of adding any weight and changing the balance of your rifle. Instead I would either have it Mag-Na-Ported or install a brake. A good recoil pad like Packmayr Decelerator will do a great job on taming the recoil pulse.

JD338
 
Back
Top