375 Chatfield Taylor

jmad_81

Handloader
Feb 14, 2007
2,945
27
Has anybody ever loaded for one?

I took a friend bear hunting this weekend, when he showed up at my house I noticed he had brought two rifles. I thought to myself "I like the way this guy thinks". We havn't known each other for very long, and this was our first hunting trip togeather. I knew his primary rifle was a M700 300 RUM shooting a 168 TTSX, so I asked him what his back up was. He looked at me and told me that it was a 375/338WM (375 Chatfield Taylor) that he had built for his sienor project in high school. He hand carved the wood stock, did the barrel work, blued it, and bedded it. Then he tells me that he is giving it to my 3 month old boy! I protested, but he would not hear any of it. I greatfully excepted it for my boy Barrett, as I'm not sure he could ever pick up a box of shells for it yet.

From what I can tell, it doesn't lack much to a 375 H&H with any bullet under 260 grs. Looking at 3000 fps with a 225, and in the 2600 range with a 270 gr bullet. Should be one hell of a dark timber elk whacker! Didn't know if anybody here had any experience with one, and could point me in a good direction. QL suggests RL-17 as one of the faster powders.
 
Yeah!

When he got home he went through his safe and called me back and said he has a 250-3000 that he built with another hand carved stock that he wants to give to my daughter, Payton. I started to protest again and he just told me to stop. He said he has three safes full of rifles, and he can't decided what one to take most of the time, and it ment alot to him to be able to give them to pople that will love them.
 
Jake,

That is awesome! Post a picture of the rifle and a shell for all of us to see.

JD338
 
Dude! I need to hook up with your friends! :)

Let me dig around a bit... I seem to recall a Handloader Magazine I have with some load data for it. I can scan it and send it to you.
 
Does this guy need any work done around his home? I'm a skilled electrician, plumber with some HVAC knowledge, and can build anything given enough time. Car and small engine repairs? PC repair? I can clean guns like a madman.
Heck I'd even be his Gurhkan porter wherever he wants to go.

:wink:
 
Jake, that is an awesome gift buddy, but I do hope you don't shoot the barrels out before your boy and girl are big enough to shoot them!!!!!

HA! Man, that brings a tear to my eye. That is a gift that just never will get old. Looking forward to the pictures buddy.. Don't hold back on us!
 
I also have that Handloader article already scanned and copied. No problem making another. Te only difference between my rifle and the one in the article is he had a bit longer barrel and I have mine in a Ramline stock. Duplication .375 H&H velocity is a piece of cake. I worked up to the level in the article with the .270 gr. Hornady spire point and the .300 grl Hornady and Sierra Game King bullets. Accuracy in my rifle is right at MOA with all three bullets and extreme spreads were very low a 6 FPS for one load and 8 FPS for the two .300 gr. bullets.
Brass is not hard to make. Just run .338 Win. mag. through the die, load and shoot. I've even made brass from 7MM Rem. mag but you lose a few when the neck splits. :( Easiest way to make brass I've found is use .458 Win. Mag. and run it through the FL die, then trim ever so slightly to square off the necks.
Of the loads in the article, I got the best results with IMR5350.
My rifle only weighs 7.5 pounds. You carry it a lot but shoot it little. :roll: :lol: :lol: :lol:
Right now it has an old El Paso Weaver 4X with post reticle. I still need to put iron sights on the gun but haven't been in any hurry.
FWIW, I rarely name a rifle but that one is called, "The Hammer." It hits like one at both ends. :lol: :lol: :lol:
Paul B.
 
Paul, you gotta show us a picture of the rifle buddy! Sounds very cool. I can see the hammer part! Never thought of the 375/338WM... Sounds like it would be pretty sweet.. Almost as much as the 375 Whelen!
 
I have an Interarms Mk. X in 7 RM that I've been thinking about turning into something else... .425 Express, .416 Taylor, .375-338, maybe a .358 Norma. Post enough pics, you may push me over the edge...
 
Jake,
That looks sweet! I think a gun like that needs checkering - so you can hang on when you pull the trigger! I think David posted about somebody he's used. Nice to have benefactors like that.

Scott
 
I think your right! I might have to look that up. Heck I might have to grab a few pieces of wood and try to learn how to do it myself!
 
Jake,

She is a beauty for sure. You need to get her out to the range ASAP and work up some loads. Your son is counting on you. :grin:
Pretty cool looking round too.

JD338
 
Jim, I'm a bit embarrassed to admit this, but I'm pretty much out of .375 bullets at the moment :oops: It will get a good scrubbing this week, and I'll look for some 338 WM brass that I can work up.
 
Wow, what a gift for a youngster! And, what a great senior project. If that fellow could do that at 17-18 years old, what can he do now? Very impressive and nice piece of wood.
 
Jake,

He did a beautiful job on that rifle; and he did a gracious thing in gifting your son with it and then gifting your daughter with another. That'll be a great reminder of generosity for a lifetime.
 
runtohunt":2560u7ta said:
Wow, what a gift for a youngster! And, what a great senior project. If that fellow could do that at 17-18 years old, what can he do now? Very impressive and nice piece of wood.

That thought entered my mind as well...
 
Back
Top