Load data for H 4350 150 gr. Accubond

It isn't exactly the same. Close and somewhat interchangeable, but not grain for grain usually..

Cartridge : .30-06 Spring. (SAAMI)
Bullet : .308, 150, Nosler AccuBond 56719
Useable Case Capaci: 61.286 grain H2O = 3.979 cm³
Cartridge O.A.L. L6: 3.340 inch = 84.84 mm
Barrel Length : 22.0 inch = 558.8 mm
Powder : IMR 4350

Predicted data by increasing and decreasing the given charge,
incremented in steps of 2.0% of nominal charge.
CAUTION: Figures exceed maximum and minimum recommended loads !

Step Fill. Charge Vel. Energy Pmax Pmuz Prop.Burnt B_Time
% % Grains fps ft.lbs psi psi % ms

-20.0 85 47.92 2340 1824 30747 7849 84.0 1.368
-18.0 87 49.12 2399 1917 32829 8123 85.4 1.333
-16.0 90 50.32 2458 2012 35054 8391 86.8 1.299
-14.0 92 51.51 2517 2111 37425 8654 88.1 1.265
-12.0 94 52.71 2577 2212 39983 8910 89.3 1.226
-10.0 96 53.91 2637 2316 42713 9159 90.5 1.189
-08.0 98 55.11 2697 2423 45639 9400 91.7 1.153
-06.0 100 56.31 2758 2533 48775 9632 92.7 1.119
-04.0 102 57.50 2818 2645 52150 9852 93.7 1.085 ! Near Maximum !
-02.0 104 58.70 2879 2761 55773 10062 94.7 1.053 ! Near Maximum !
+00.0 107 59.90 2940 2878 59668 10260 95.6 1.022 !DANGEROUS LOAD-DO NOT USE!
+02.0 109 61.10 3001 2999 63832 10444 96.4 0.992 !DANGEROUS LOAD-DO NOT USE!
+04.0 111 62.30 3062 3122 68313 10614 97.1 0.963 !DANGEROUS LOAD-DO NOT USE!
+06.0 113 63.49 3122 3247 73148 10769 97.7 0.935 !DANGEROUS LOAD-DO NOT USE!
+08.0 115 64.69 3184 3376 78370 10908 98.3 0.907 !DANGEROUS LOAD-DO NOT USE!
+10.0 117 65.89 3245 3506 84022 11029 98.8 0.881 !DANGEROUS LOAD-DO NOT USE!

Results caused by ± 10% powder lot-to-lot burning rate variation using nominal charge
Data for burning rate increased by 10% relative to nominal value:
+Ba 107 59.90 3086 3172 70804 10332 99.3 0.950 !DANGEROUS LOAD-DO NOT USE!
Data for burning rate decreased by 10% relative to nominal value:
-Ba 107 59.90 2753 2524 49002 9733 88.3 1.115


Cartridge : .30-06 Spring. (SAAMI)
Bullet : .308, 150, Nosler AccuBond 56719
Useable Case Capaci: 61.286 grain H2O = 3.979 cm³
Cartridge O.A.L. L6: 3.340 inch = 84.84 mm
Barrel Length : 22.0 inch = 558.8 mm
Powder : Hodgdon H4350

Predicted data by increasing and decreasing the given charge,
incremented in steps of 2.0% of nominal charge.
CAUTION: Figures exceed maximum and minimum recommended loads !

Step Fill. Charge Vel. Energy Pmax Pmuz Prop.Burnt B_Time
% % Grains fps ft.lbs psi psi % ms

-20.0 87 48.08 2341 1826 30807 7859 83.9 1.367
-18.0 89 49.28 2400 1919 32899 8133 85.3 1.332
-16.0 91 50.48 2460 2015 35135 8403 86.6 1.297
-14.0 94 51.69 2519 2114 37527 8667 88.0 1.263
-12.0 96 52.89 2579 2216 40086 8924 89.2 1.224
-10.0 98 54.09 2640 2321 42834 9174 90.4 1.187
-08.0 100 55.29 2700 2428 45777 9416 91.6 1.151
-06.0 102 56.49 2761 2538 48937 9649 92.6 1.117
-04.0 104 57.70 2821 2651 52331 9871 93.7 1.083 ! Near Maximum !
-02.0 107 58.90 2882 2767 55982 10082 94.6 1.051 ! Near Maximum !
+00.0 109 60.10 2943 2886 59908 10280 95.5 1.020 !DANGEROUS LOAD-DO NOT USE!
+02.0 111 61.30 3005 3007 64112 10466 96.3 0.990 !DANGEROUS LOAD-DO NOT USE!
+04.0 113 62.50 3066 3130 68634 10636 97.0 0.961 !DANGEROUS LOAD-DO NOT USE!
+06.0 115 63.71 3127 3257 73515 10792 97.7 0.933 !DANGEROUS LOAD-DO NOT USE!
+08.0 117 64.91 3188 3386 78792 10931 98.3 0.905 !DANGEROUS LOAD-DO NOT USE!
+10.0 120 66.11 3250 3517 84506 11053 98.8 0.879 !DANGEROUS LOAD-DO NOT USE!

Results caused by ± 10% powder lot-to-lot burning rate variation using nominal charge
Data for burning rate increased by 10% relative to nominal value:
+Ba 109 60.10 3091 3181 71115 10358 99.3 0.948 !DANGEROUS LOAD-DO NOT USE!
Data for burning rate decreased by 10% relative to nominal value:
-Ba 109 60.10 2756 2530 49195 9747 88.2 1.113


Lot to lot differences in the two would be enough for me to drop back a little before trying to swap them grain for grain.
 
SJB358":1o0gwpa8 said:
It isn't exactly the same. Close and somewhat interchangeable, but not grain for grain usually..

Cartridge : .30-06 Spring. (SAAMI)
Bullet : .308, 150, Nosler AccuBond 56719
Useable Case Capaci: 61.286 grain H2O = 3.979 cm³
Cartridge O.A.L. L6: 3.340 inch = 84.84 mm
Barrel Length : 22.0 inch = 558.8 mm
Powder : IMR 4350

Predicted data by increasing and decreasing the given charge,
incremented in steps of 2.0% of nominal charge.
CAUTION: Figures exceed maximum and minimum recommended loads !

Step Fill. Charge Vel. Energy Pmax Pmuz Prop.Burnt B_Time
% % Grains fps ft.lbs psi psi % ms

-20.0 85 47.92 2340 1824 30747 7849 84.0 1.368
-18.0 87 49.12 2399 1917 32829 8123 85.4 1.333
-16.0 90 50.32 2458 2012 35054 8391 86.8 1.299
-14.0 92 51.51 2517 2111 37425 8654 88.1 1.265
-12.0 94 52.71 2577 2212 39983 8910 89.3 1.226
-10.0 96 53.91 2637 2316 42713 9159 90.5 1.189
-08.0 98 55.11 2697 2423 45639 9400 91.7 1.153
-06.0 100 56.31 2758 2533 48775 9632 92.7 1.119
-04.0 102 57.50 2818 2645 52150 9852 93.7 1.085 ! Near Maximum !
-02.0 104 58.70 2879 2761 55773 10062 94.7 1.053 ! Near Maximum !
+00.0 107 59.90 2940 2878 59668 10260 95.6 1.022 !DANGEROUS LOAD-DO NOT USE!
+02.0 109 61.10 3001 2999 63832 10444 96.4 0.992 !DANGEROUS LOAD-DO NOT USE!
+04.0 111 62.30 3062 3122 68313 10614 97.1 0.963 !DANGEROUS LOAD-DO NOT USE!
+06.0 113 63.49 3122 3247 73148 10769 97.7 0.935 !DANGEROUS LOAD-DO NOT USE!
+08.0 115 64.69 3184 3376 78370 10908 98.3 0.907 !DANGEROUS LOAD-DO NOT USE!
+10.0 117 65.89 3245 3506 84022 11029 98.8 0.881 !DANGEROUS LOAD-DO NOT USE!

Results caused by ± 10% powder lot-to-lot burning rate variation using nominal charge
Data for burning rate increased by 10% relative to nominal value:
+Ba 107 59.90 3086 3172 70804 10332 99.3 0.950 !DANGEROUS LOAD-DO NOT USE!
Data for burning rate decreased by 10% relative to nominal value:
-Ba 107 59.90 2753 2524 49002 9733 88.3 1.115


Cartridge : .30-06 Spring. (SAAMI)
Bullet : .308, 150, Nosler AccuBond 56719
Useable Case Capaci: 61.286 grain H2O = 3.979 cm³
Cartridge O.A.L. L6: 3.340 inch = 84.84 mm
Barrel Length : 22.0 inch = 558.8 mm
Powder : Hodgdon H4350

Predicted data by increasing and decreasing the given charge,
incremented in steps of 2.0% of nominal charge.
CAUTION: Figures exceed maximum and minimum recommended loads !

Step Fill. Charge Vel. Energy Pmax Pmuz Prop.Burnt B_Time
% % Grains fps ft.lbs psi psi % ms

-20.0 87 48.08 2341 1826 30807 7859 83.9 1.367
-18.0 89 49.28 2400 1919 32899 8133 85.3 1.332
-16.0 91 50.48 2460 2015 35135 8403 86.6 1.297
-14.0 94 51.69 2519 2114 37527 8667 88.0 1.263
-12.0 96 52.89 2579 2216 40086 8924 89.2 1.224
-10.0 98 54.09 2640 2321 42834 9174 90.4 1.187
-08.0 100 55.29 2700 2428 45777 9416 91.6 1.151
-06.0 102 56.49 2761 2538 48937 9649 92.6 1.117
-04.0 104 57.70 2821 2651 52331 9871 93.7 1.083 ! Near Maximum !
-02.0 107 58.90 2882 2767 55982 10082 94.6 1.051 ! Near Maximum !
+00.0 109 60.10 2943 2886 59908 10280 95.5 1.020 !DANGEROUS LOAD-DO NOT USE!
+02.0 111 61.30 3005 3007 64112 10466 96.3 0.990 !DANGEROUS LOAD-DO NOT USE!
+04.0 113 62.50 3066 3130 68634 10636 97.0 0.961 !DANGEROUS LOAD-DO NOT USE!
+06.0 115 63.71 3127 3257 73515 10792 97.7 0.933 !DANGEROUS LOAD-DO NOT USE!
+08.0 117 64.91 3188 3386 78792 10931 98.3 0.905 !DANGEROUS LOAD-DO NOT USE!
+10.0 120 66.11 3250 3517 84506 11053 98.8 0.879 !DANGEROUS LOAD-DO NOT USE!

Results caused by ± 10% powder lot-to-lot burning rate variation using nominal charge
Data for burning rate increased by 10% relative to nominal value:
+Ba 109 60.10 3091 3181 71115 10358 99.3 0.948 !DANGEROUS LOAD-DO NOT USE!
Data for burning rate decreased by 10% relative to nominal value:
-Ba 109 60.10 2756 2530 49195 9747 88.2 1.113


Lot to lot differences in the two would be enough for me to drop back a little before trying to swap them grain for grain.
I'll have to see if hodgdon has data for 150 gr. 3006
 
MrMinks2":2p1nt61z said:
http://www.hodgdonreloading.com/data/rifle
Thank you Mr.Minks2, I e mailed that to my address.

My swift #2 manual has this data h 4350 for all sciroccos and a frames.

I haven't bought any Swifts yet , just the NABs in 150 gr.
 
It looks like H 4350 is a few grains higher in charge weight than imr 4350 for 150 gr. Pills
 
I have used limited quantities of 150 ABs with 59.5ish grains H4350 with pretty good results. Then I switched to all 180 PTs for all my hunting, so I haven't done more with the 150s. Good luck!
 
Barnes didn't have data for the .308 caliber 180 grain TTSX fitted in a 30-06 so I called them and used the data for the H 4350. Using the data for H 4350 and using IMR 4350 I found a load that shoots 1/2 MOA in my rifle. It's a max H 4350 load but I'm using IMR 4350. Not showing any pressure signs and it's a great load.

Sent from my SGH-M919 using Tapatalk
 
Back
Top