QL for 300 weatherby with a 208 grain hornady eld

Ridgegoat90

Beginner
Apr 24, 2016
17
0
I am looking to load up my 300 weatherby with some 208 hornady eld's and of course cannot find any info. Would somebody please run a QL for this cartridge/bullet combo? Thanks
 
here it is .

300 wby cartridge is rated at 63817PSI .


Cartridge : .300 Weath. Mag.
Bullet : .308, 208, Hornady ELDMatch 30731
Useable Case Capaci: 86.757 grain H2O = 5.633 cm³
Cartridge O.A.L. L6: 3.560 inch = 90.42 mm
Barrel Length : 26.0 inch = 660.4 mm
Powder : Alliant Reloder-26

Predicted data by increasing and decreasing the given charge,
incremented in steps of 2.0% of nominal charge.
CAUTION: Figures exceed maximum and minimum recommended loads !

Step Fill. Charge Vel. Energy Pmax Pmuz Prop.Burnt B_Time
% % Grains fps ft.lbs psi psi % ms

-20.0 75 64.40 2440 2750 31892 10757 98.9 1.745
-18.0 77 66.01 2500 2887 34213 10980 99.5 1.699
-16.0 79 67.62 2560 3026 36709 11174 99.8 1.654
-14.0 81 69.23 2619 3168 39398 11339 100.0 1.602
-12.0 82 70.84 2677 3311 42259 11477 100.0 1.550
-10.0 84 72.45 2735 3455 45296 11609 100.0 1.502
-08.0 86 74.06 2792 3600 48537 11737 100.0 1.454
-06.0 88 75.67 2848 3746 51998 11862 100.0 1.409
-04.0 90 77.28 2904 3894 55697 11983 100.0 1.366 ! Near Maximum !
-02.0 92 78.89 2959 4043 59650 12100 100.0 1.324 ! Near Maximum !
+00.0 94 80.50 3014 4194 63878 12214 100.0 1.284 !DANGEROUS LOAD-DO NOT USE!
+02.0 96 82.11 3068 4347 68403 12324 100.0 1.246 !DANGEROUS LOAD-DO NOT USE!
+04.0 97 83.72 3122 4501 73250 12430 100.0 1.209 !DANGEROUS LOAD-DO NOT USE!
+06.0 99 85.33 3175 4657 78448 12532 100.0 1.173 !DANGEROUS LOAD-DO NOT USE!
+08.0 101 86.94 3229 4815 84027 12629 100.0 1.139 !DANGEROUS LOAD-DO NOT USE!
+10.0 103 88.55 3282 4976 90023 12721 100.0 1.106 !DANGEROUS LOAD-DO NOT USE!

Results caused by ± 10% powder lot-to-lot burning rate variation using nominal charge
Data for burning rate increased by 10% relative to nominal value:
+Ba 94 80.50 3116 4485 78553 11791 100.0 1.184 !DANGEROUS LOAD-DO NOT USE!
Data for burning rate decreased by 10% relative to nominal value:
-Ba 94 80.50 2855 3765 49415 12833 100.0 1.424
 
Ridgegoat90":1s1phhxu said:
Thank you much. Dont have the funds to cover buying my own QL yet. Hopefully soon



you're welcome .

let me know how this works out for you . I recently bought a pound of RL26 to play with . after hunting season I'm going to give it a try in my 300 wby , and also in my 7 rem mag . maybe I can get two rifles to use the same powder .
 
I have been using re26 in my 220 swift pushing 75 a-max's around 3500, and have been getting great results. Smallest 5 shot group measured .156 center to center at widest point. SD's are fantastic as well at higher pressures with powder level being around the base of the neck. SD for that load was 11. I shot some test loads last weekend and got 3000 fps with 81 grains of re26 (!!!Hot load, may not be safe in your rifle, please start at safe book load and work up!!!) And very consistent velocities. Groups were not great, but i had forgotten that the bedding relationship on that rifle was poor, so I bedded it and we will see what it does tomorrow morning. Groups would have two touching, and then another two touching ect ect which to me was a bedding issue. I love the powder so far. Will post pics tomorrow hopefully!
 
Back
Top