- Thread starter
- #21
RL338
Handloader
- Mar 23, 2017
- 3,290
- 5,320
9lb unbraked 300 Wby with that load is like a wrecking ball
Cheap .30cal Heavyweights
- Thread starter RL338
- Start date
- Nov 4, 2004
- 25,213
- 8,524
And those loads definitely have the cool factor going for them too.
JD338
JD338
- Thread starter
- #23
RL338
Handloader
- Mar 23, 2017
- 3,290
- 5,320
This evening I moved onto the 308 Win. with these. Goal I set was 2500fps. Powder I used was Superformance with Alcan LRM primers. I only had some odd and end brass laying around. 1 group has 57.15grs H2O and the other 58grs H2O. I used the 57.15 for pressure test. Started at 41grs , way slow. Moved up to 46grs , getting there. 50grs is where it’s at.
41grs - 1893fps
46grs - 2198fps
50grs - 2509fps
51grs - 2522fps
52grs - 2590fps
I loaded all brass at 50grs with 1/4 turn crimp.
I fired 1 round of 58gr H2O brass , was a little slower as expected.
50grs - 2469fps
Just for fun I checked how much of Superformance a fired case holds.
57.15gr H2O holds 61.0grs
58.0gr H2O holds 62.2grs
I will get these in paper at some point , hopefully it will match the 30-06 results.
41grs - 1893fps
46grs - 2198fps
50grs - 2509fps
51grs - 2522fps
52grs - 2590fps
I loaded all brass at 50grs with 1/4 turn crimp.
I fired 1 round of 58gr H2O brass , was a little slower as expected.
50grs - 2469fps
Just for fun I checked how much of Superformance a fired case holds.
57.15gr H2O holds 61.0grs
58.0gr H2O holds 62.2grs
I will get these in paper at some point , hopefully it will match the 30-06 results.
- Nov 4, 2004
- 25,213
- 8,524
- Nov 4, 2004
- 25,213
- 8,524
- Thread starter
- #26
RL338
Handloader
- Mar 23, 2017
- 3,290
- 5,320
With that momentum of 220grs , it’s quite a thumper round.
DrMike
Ballistician
- Nov 8, 2006
- 37,330
- 6,021
I should imagine that mass pushed at that velocity would work for a wide variety of heavy game.
filmjunkie4ever
Handloader
- May 4, 2011
- 1,936
- 1,249
For whatever reason, I always figured to load these in a .300 H&H if I ever got one. Its a great deal on the bullets in any case!
wvbuckbuster
Handloader
- Nov 5, 2015
- 2,645
- 2,310
Impressive. What distance was your jug test? Dan.
- Nov 4, 2004
- 25,213
- 8,524
TackDriver284
Handloader
- Feb 13, 2016
- 2,534
- 2,056
Impressive
Joec7651
Handloader
- Apr 7, 2019
- 949
- 1,220
Wow! I’m really impressed with your velocity results. Almost 2600 fps is more than I thought you’d get from a 308 Win shooting 220 grain bullets. That’s a stout load.
- Thread starter
- #34
RL338
Handloader
- Mar 23, 2017
- 3,290
- 5,320
The brass I used was old Winchester with a larger volume. Even with that long 220gr bullet at 50grs it was just touching the powder. Superformance load data for 7mm-08 looked good so I gave it a whirl.
TackDriver284
Handloader
- Feb 13, 2016
- 2,534
- 2,056
I'm impressed that you could fill 50 grains of ball powder and seat 220 grains on it, did it have a crush? I never liked a crush with over 45 grains using stick powders that seats deep in my 308 case, even with a drop tube. I don't crimp and neck tension is no more than 1 -2 thou. I keep the bullets .005 thousands off or more. When I seat bullets, I don't like to force seat them. When I do developments in .3 increments from 43 up to 46, my caliper measurements are not consistent when going past 44 grains because of the crush fit. I use Lapua brass and they do have less volume than the Winchester cases, if I could remember. I have only loaded 178 grain bullets or lighter in mine. At 178 grains, I'm able to run about 2725 fps with 43.5 grains of Varget, not a hot load. Your 2600 fps with 220 grains is a killer load with mass.
- Thread starter
- #36
RL338
Handloader
- Mar 23, 2017
- 3,290
- 5,320
Well the 308 Win didn’t have a great showing with the 220s. Had to fight wind and rain today , like every day since mid spring.
- Nov 4, 2004
- 25,213
- 8,524
