Powder Coating Bullets

truck driver

Ammo Smith
Mar 11, 2013
7,608
1,569
Not my first Rodeo doing this but the first time I had them shoot good for me out of my 1911 .45.
I cast my own bullets to cut the cost down for practice ammo. Though my cast bullets shoot as good or better than the commercially machine cast you can buy, the commercially swaged lead bullets are more consistent and more accurate at 50yds and for the most part will shoot right alongside jacketed bullets.
The downside of cast bullets is they are dirtier than jacketed bullets leaving lubricant grease deposits in the gun, powder coat like copper jacket bullets use no bullet lubricants.
I use dry powder and use a method called shake and bake to apply the paint. My tools are a poly plastic bowl with a sealable lid that has the #5 recycle code on the bottom, most food packaging plastic containers have this code in a triangle on the bottom, think Cool Whip and the clean empty container with the lid will get you started, some black 5mm airsoft plastic BBs will help create enough static electricity to help the paint to coat the bullets, a cheap toaster oven with a built in air frier makes it easier to get even heat flowing over the bullets and is what I use some flat trays or aluminum cake/pie pans for the bullets to set in the oven , a cheap oven thermometer so you can control the oven temperature set for 400 degrees and a pair of Harbor freight tweezers to pick up the coated bullets to put on the trays after coating, a pair of nitril gloves to keep your hands and bullets clean.
pictures of coated bullets and targets shot at 25yds off a rest to get the best accuracy and a chronograph to check your velocity. The first target is five shots to check the accuracy and the second target is 20 shots to check for fliers.image0 (3) powder coat 4.1 TG.jpegimage1 (2) powdercoat 20shots .jpegimage0 (3)powder coat 1.jpegimage6 powder coat 4.jpegimage7 (1) powder coat 6.jpeg
 
Glad to see someone else doing this on the forum! I haven't done it yet but got a couple different powder colors and some of the other supplies. I've been casting on and off for about 15 years and have even killed quite a few deer with cast in revolvers. Hoping once I get done moving into this new house, I'll dive into the powder coating after deer season.

Which powders have you been trying?
 
I've tried using lots of different powders over the years. I really like high gloss powders, they feel slick to me and hopefully that helps them slide down the barrel.

Only time I've used the acetone method was with I believe it's called hitek powder. Not sure if they sell it anymore, last time I checked all I turned up out of stock.

Generally use a cheap HF powder coating gun and spray my bullets. I got a cheap toaster oven and pans from Goodwill, cut one of the roasting pans to fit upside down in the rail cuts in the oven, and just drilled 100 self tapping screws into the bottom of the pan. I stand my bullets on the bolts to spray so it doesn't stick to the pan and to get a little wrap around on the bullet base. Grind the layers off around the bullets when the build up is too much or find another pan and make a new one.

PXL_20261121_123131384.jpg
 
Glad to see someone else doing this on the forum! I haven't done it yet but got a couple different powder colors and some of the other supplies. I've been casting on and off for about 15 years and have even killed quite a few deer with cast in revolvers. Hoping once I get done moving into this new house, I'll dive into the powder coating after deer season.

Which powders have you been trying?
I have tried Harbor Freight and found a fellow on Cast Boolets forum who sells powder by the pound out of NC.
The Cast Boolets forum is where I have learned how to powder coat bullets.
My technique for coating comes from what others have found that works best for them.
The Harbor Freight or Eastwood spray guns are not needed to get a good coat and just adds expense to the process, quality hand cast bullets are required for good accuracy.
I'll take some pictures of my equipment and post to try and help you get started.
 
I've tried using lots of different powders over the years. I really like high gloss powders, they feel slick to me and hopefully that helps them slide down the barrel.

Only time I've used the acetone method was with I believe it's called hitek powder. Not sure if they sell it anymore, last time I checked all I turned up out of stock.

Generally use a cheap HF powder coating gun and spray my bullets. I got a cheap toaster oven and pans from Goodwill, cut one of the roasting pans to fit upside down in the rail cuts in the oven, and just drilled 100 self tapping screws into the bottom of the pan. I stand my bullets on the bolts to spray so it doesn't stick to the pan and to get a little wrap around on the bullet base. Grind the layers off around the bullets when the build up is too much or find another pan and make a new one.

View attachment 30624
I only use acetone to check after baking to make sure the powder/paint is fully cured. Wet a paper towel with the acetone and wipe the tip of the bullet to see if any coating wipes off. I try to keep everything simple and uncomplicated.
 
Back
Top