Search results

Well when I was finished with this little experiment I tried a couple and cant close the bolt on the 260 the OAL on the brass is fine the problem is at the rim I think ? It was cheap PMC 308 brass that I ran threw the M1A1 so no loss but I have had no problems with going the other way with 243...

I necked down some 308 brass today to 260 rem any problem, that you guys see. Jon

I shoot 180 AB's and get great results at about 2930 fps. I shoot a Remington 700 bdl stainless 1995 model 24" barrel. 180g NAB with 75g H4831sc backit off about 3 grains and work up, I get 3/4 in groups and 74 was no change just 60 fps more at 75g.

75g H4831 start at 74 and work up I get 3/4 in groups. Good Luck. Jon

I have not measured the concentricity, I went to the range today and am getting 8 in groups at 500 so cant complain but I am going to keep working on it. Jon

Well I am .039 off the lands, and I am getting 3010 ave. The Nosler volume 6 says for IMR 4350 43.5 to 47.5 max with 43.5 being best but it was really no better? I was hoping to get the partitions shooting for my daughters deer and elk season. Powders on hand H4895, RL15, RL19, Rl22, H4831sc...

Ok guys here is a 100g npt and a 100g A-Max they were both sitting on nosler brass and 44g of IMR 4350. The npt while shooting fair to poorly, vs the A-max which will shoot the lights out. So what do you think more or less powder seat it deeper or shallower I am a little baffled npt's usually...

I know the speed is good and well under book max for powder. If I go up even 1/2 g on powder the velocities get a little jumpy. so that seems to be the sweet spot. I am getting between 3060 to 3080 so it is really consistent with most 3070 to 3077. I was just trying to tighten it up a little, I...

Hay guys I hate to rehash this post but as we are all trying to make improvement's. I started tinkering with my 338 rum and discovered that I am .256 off the lands with a Nosler 250g AB. Well what I am getting at is this seem way off the lands I was thinking that with a the AB, I would have been...

Well I am on the road in Japan right now so I cant go into the garage right now and look but I think they are Remington 7 1/2 primers and the brass is mixed from black hills reloads and Remington. I don't know the COL off the top of my head but the gun is not particular is shoots factory...

I shoot 55gr nbt's out of my savage 110 223 and get one hole groups with 28.5 gr of blc2 and it shoots just about everything under an inch. Jon

My velocities have fallen off a bit with 4831sc in the last few years, 3095 in the 300wm with 75 gr to about 2930 and really cant stoke it much more but still shooting great groups. Fwood

75 gr 4831sc Remington 700 24 inch barrel. VLD's and NAB.

180 gr npt or nab with 75.4 grans of 4831sc or 78 gr of 4831sc and a 165 npt boom dead.

It appears to be a WMR cylinder there is no gun. Jon

I just have the cylinder not the gun. It was in a box I was going threw. Jon

I just came into a Ruger Single Six cylinder 22 cal, it is blue, and brand new in the box. I am guessing it is 15 or more years old. Does anyone know what it might be worth? If anything. Jon

I have had the same problem, I bought some Nosler brass and it is ok. I found one lot of 2000 but it was a bit too pricy for me. There is some at times on gun broker but it is expensive as well. It seems like a dying round. I like mine though. Jon

I shoot a muley or two every year and have used a lot of different calibers. I prefer my 270 win. I have used every thing from 100 gr. bronze points to 130 gr npt. I haven't found them to be bullet proof at all. If you make a decent shot they go down. I have gone threw a few stages on bullet...

338 rum is a big hammer. I have only shot two animals with mine, an Alaskan Bull Moose and a Rocky Mountain Bull Elk. The moose was at 98 yards on the range finder and the elk was 364 yards I think. Same result one shot and dead critter. I have had the same results with my 300 and 270 on other...