wisconsinteacher
Handloader
- Dec 2, 2010
- 1,984
- 301
I'm looking for 7-08 brass and found some PRVI in stock. Just wondering if this is good stuff?
Prvi Brass??
- Thread starter wisconsinteacher
- Start date
mjcmichigan
Handloader
- Dec 26, 2016
- 2,412
- 378
I used it for Savage 303. It seemed fine. No issues with quality and the 303 shot great with it. Best IMO is more like Norma, Lapua.
6.5_sWv
Beginner
- Mar 5, 2019
- 213
- 214
I've used it for 8x57 and 7mm Mag. It won't be Lapua quality but it's very decent. I've had no issues with what I've used
wvbuckbuster
Handloader
- Nov 5, 2015
- 3,174
- 3,501
Have used it in 270 Win and 9mm Luger with no issues. Dan.
I've seen quite a few reports on Privi ammo and brass, most of it good and none of it bad. The only complaint I've heard of was sometimes you need to order a different shell holds if loading the 7x57 and 8x57. I have some Aussie 7x57 factory ammo that is loaded with Privi brass and I tried them in my normal 30-06 shell holder and they all fit just fine. The ammo is loaded with a 120 gr. HP monometal bullet. I haven't shot any as of yet so no idea on how well they will shoot in my rifle.
Paul B.
Paul B.
Good stuff. I've used it in 6.5x55 and 7-08. It's the only new brass I've used for my 7-08. Seems to withstand irresponsible doses of staball 6.5 and mag primers better than the once fired remington brass I had on hand. Nearing the third load cycle on the first 50 pieces I bought, we'll see how the primer pockets are faring. Just bought 150 more pieces. Their brass seems to be favorably comparable to most of our domestic manufacturers. I don't weigh cases or measure internal volume or worry about flashholes, I'm loading for hunting rifles. I have worked up some extremely accurate loads with prvi components with little fuss, use it with confidence.
Jimbeaux82
Handloader
- Jan 6, 2011
- 416
- 195
Good stuff. I have used it in many calibers; 223, 6.5x55, 7x57, 8x57, 308, 30/06, 270 never had a problem. Just as good as Win or REM in my opinion
DrMike
Ballistician
- Nov 8, 2006
- 38,028
- 7,970
I've used Privi brass in 8X57, 7X57 and a few other chamberings. I was always pleased with it.
hunter24605
Handloader
- Apr 30, 2016
- 2,748
- 5,117
I have used a ton of in 308 with no issues..I also used a bunch of my 308 brass to make 7-08 brass when it was near impossible to find..Produced some very accurate loads for the daughter's 7-08.
HodgemanAK
Beginner
- Oct 23, 2020
- 240
- 220
A friend of mine has loaded some 7-08 and some 243 in PRVI... works fine.
KinleyWater
Handloader
- Jun 15, 2019
- 1,140
- 1,596
I've used .308 recovered from factory loads. Did nothing special other than full-length size and trim and have 3 and 4 loads (including the factory) through some of them. I don't load for velocity in .308, just a good general purpose 150 or 180 gr SP load. I don't know what your end purpose is, but I cannot imagine the Prvi would be inadequate for anything other than perhaps very precise target shooting.
Speaking of it if anybody needs some 30/06 brass PV has some at decent price. Not much left.
www.powdervalleyinc.com
Prvi Partizan 30-06 Springfield Brass 50 Count
Prvi Partizian Unprimed Brass 30-06 Springfield (50) WARNING: This product can expose you to Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to – www.P65Warnings.ca.gov.
www.powdervalleyinc.com
