QuickLoad questions thread...
- Thread starter Ridgerunner665
- Start date
Dwh7271":zo98bcug said:
I just found this sticky, and I'm glad I did. I've owned QL for several years but don't feel like I've really fully used it. Re: QuickDesign, I have a copy as well. I like wildcats, so marrying the two has been very helpful in getting started on load development. One question: Does any sort of repository exist for QD users to exchange wildcat cartridge files (.ctg format)?
Couldn't find that bullet in the database. Ran 52 gr CC instead.
Code:
Cartridge : .22 Nosler
Bullet : .224, 52, Nosler CC HPBT 53294
Useable Case Capaci: 32.676 grain H2O = 2.122 cm³
Cartridge O.A.L. L6: 2.260 inch = 57.40 mm
Barrel Length : 20.0 inch = 508.0 mm
Powder : Hodgdon CFE223
Predicted data by increasing and decreasing the given charge,
incremented in steps of 0.894% of nominal charge.
CAUTION: Figures exceed maximum and minimum recommended loads !
Step Fill. Charge Vel. Energy Pmax Pmuz Prop.Burnt B_Time
% % Grains fps ft.lbs psi psi % ms
-08.9 91 30.57 3157 1151 42130 10058 89.6 0.959
-08.0 92 30.87 3191 1176 43471 10183 90.2 0.945
-07.2 93 31.17 3226 1202 44862 10306 90.8 0.931
-06.3 94 31.47 3260 1228 46300 10427 91.4 0.918
-05.4 95 31.77 3295 1254 47790 10545 92.0 0.904
-04.5 96 32.07 3330 1281 49334 10660 92.5 0.891
-03.6 96 32.37 3365 1308 50933 10772 93.1 0.878 ! Near Maximum !
-02.7 97 32.67 3400 1335 52591 10881 93.6 0.866 ! Near Maximum !
-01.8 98 32.97 3435 1363 54310 10986 94.1 0.853 ! Near Maximum !
-00.9 99 33.27 3470 1391 56068 11089 94.6 0.841 ! Near Maximum !
+00.0 100 33.57 3505 1419 57941 11187 95.1 0.829 ! Near Maximum !
+00.9 101 33.87 3540 1448 59852 11282 95.5 0.817 !DANGEROUS LOAD-DO NOT USE!
+01.8 102 34.17 3576 1477 61851 11373 95.9 0.805 !DANGEROUS LOAD-DO NOT USE!
+02.7 103 34.47 3611 1506 63920 11461 96.4 0.793 !DANGEROUS LOAD-DO NOT USE!
+03.6 104 34.77 3646 1535 66069 11544 96.7 0.782 !DANGEROUS LOAD-DO NOT USE!
+04.5 104 35.07 3682 1565 68301 11623 97.1 0.771 !DANGEROUS LOAD-DO NOT USE!
Results caused by ± 3% powder lot-to-lot burning rate variation using nominal charge
Data for burning rate increased by 3% relative to nominal value:
+Ba 100 33.57 3572 1473 61487 11286 96.8 0.808 !DANGEROUS LOAD-DO NOT USE!
Data for burning rate decreased by 3% relative to nominal value:
-Ba 100 33.57 3434 1362 54538 11034 93.0 0.852 ! Near Maximum !I’m not sure if this is the right spot for a request? If not please disregard.
I’m having trouble getting a load that is over 3000fps (180gr) for a 300winmag and accurate. I have found an average on but its so damn slow it’s boring lol.
I would love to get a time in the barrel to look for a node or point me close to it.
I have all the info you should need;
Model 70 Supergrade with 24” barrel
Case capacity in h2o: 93.6gr
Case length: 2.602”
COAL: 3.515 (does not fit the mag fyi) (trying to track down a 375h&h box etc)
Projectile Nosler BT 180gr - 30180 part no
Powder is ADI2217 or H1000 (same) @ 81grs
Using a Fed 215M primer.
This load has given me 3020fps average through a shooting chrony.
Many thanks to anyone who could spend the time to run this through their program.
Cheers
Anthony
I’m having trouble getting a load that is over 3000fps (180gr) for a 300winmag and accurate. I have found an average on but its so damn slow it’s boring lol.
I would love to get a time in the barrel to look for a node or point me close to it.
I have all the info you should need;
Model 70 Supergrade with 24” barrel
Case capacity in h2o: 93.6gr
Case length: 2.602”
COAL: 3.515 (does not fit the mag fyi) (trying to track down a 375h&h box etc)
Projectile Nosler BT 180gr - 30180 part no
Powder is ADI2217 or H1000 (same) @ 81grs
Using a Fed 215M primer.
This load has given me 3020fps average through a shooting chrony.
Many thanks to anyone who could spend the time to run this through their program.
Cheers
Anthony
SF,
Grouping is average at best, I was wondering what QL would put the pmax at so I can load up a little. I have tried AR2213sc (H4831sc) with little success.
I have tried seating depths but am open to suggestions. With the powder load the depth I quoted seemed best. It approx 40thou off lands.
What powder do you recommend?
Grouping is average at best, I was wondering what QL would put the pmax at so I can load up a little. I have tried AR2213sc (H4831sc) with little success.
I have tried seating depths but am open to suggestions. With the powder load the depth I quoted seemed best. It approx 40thou off lands.
What powder do you recommend?
DrMike
Ballistician
- Nov 8, 2006
- 37,041
- 5,355
AnthonyC":3jyhelj1 said:
Code:
Cartridge : .300 Win. Mag.(SAAMI)
Bullet : .308, 180, Nosler BalTip 30180
Useable Case Capaci: 85.117 grain H2O = 5.527 cm³
Cartridge O.A.L. L6: 3.515 inch = 89.28 mm
Barrel Length : 24.0 inch = 609.6 mm
Powder : ADI AR 2217
Predicted data by increasing and decreasing the given charge,
incremented in steps of 1.0% of nominal charge.
CAUTION: Figures exceed maximum and minimum recommended loads !
Step Fill. Charge Vel. Energy Pmax Pmuz Prop.Burnt B_Time
% % Grains fps ft.lbs psi psi % ms
-10.0 99 76.68 2759 3043 43707 12299 95.3 1.339
-09.0 100 77.53 2794 3121 45327 12448 95.8 1.316
-08.0 101 78.38 2830 3201 47015 12591 96.4 1.293
-07.0 102 79.24 2865 3281 48774 12727 96.9 1.271
-06.0 103 80.09 2901 3363 50609 12855 97.3 1.249
-05.0 104 80.94 2936 3446 52523 12977 97.8 1.227
-04.0 105 81.79 2972 3529 54520 13090 98.2 1.206 ! Near Maximum !
-03.0 106 82.64 3007 3614 56604 13196 98.5 1.185 ! Near Maximum !
-02.0 108 83.50 3043 3700 58781 13293 98.8 1.164 ! Near Maximum !
-01.0 109 84.35 3078 3787 61057 13381 99.1 1.144 ! Near Maximum !
+00.0 110 85.20 3114 3875 63437 13461 99.4 1.124 !DANGEROUS LOAD-DO NOT USE!
+01.0 111 86.05 3149 3964 65926 13532 99.6 1.105 !DANGEROUS LOAD-DO NOT USE!
+02.0 112 86.90 3185 4054 68532 13592 99.7 1.086 !DANGEROUS LOAD-DO NOT USE!
+03.0 113 87.76 3220 4145 71262 13644 99.9 1.067 !DANGEROUS LOAD-DO NOT USE!
+04.0 114 88.61 3256 4236 74124 13686 99.9 1.048 !DANGEROUS LOAD-DO NOT USE!
+05.0 115 89.46 3291 4328 77125 13717 100.0 1.030 !DANGEROUS LOAD-DO NOT USE!
Results caused by ± 10% powder lot-to-lot burning rate variation using nominal charge
Data for burning rate increased by 10% relative to nominal value:
+Ba 110 85.20 3268 4268 77673 12927 100.0 1.034 !DANGEROUS LOAD-DO NOT USE!
Data for burning rate decreased by 10% relative to nominal value:
-Ba 110 85.20 2894 3347 51198 13158 93.4 1.240
Code:
Cartridge : .300 Win. Mag.(SAAMI)
Bullet : .308, 180, Nosler BalTip 30180
Useable Case Capaci: 85.117 grain H2O = 5.527 cm³
Cartridge O.A.L. L6: 3.515 inch = 89.28 mm
Barrel Length : 24.0 inch = 609.6 mm
Powder : Hodgdon H4831 SC
Predicted data by increasing and decreasing the given charge,
incremented in steps of 1.0% of nominal charge.
CAUTION: Figures exceed maximum and minimum recommended loads !
Step Fill. Charge Vel. Energy Pmax Pmuz Prop.Burnt B_Time
% % Grains fps ft.lbs psi psi % ms
-10.0 89 70.74 2738 2996 45304 11681 94.8 1.330
-09.0 90 71.53 2769 3064 46844 11822 95.2 1.309
-08.0 91 72.31 2800 3134 48430 11959 95.7 1.289
-07.0 92 73.10 2831 3204 50065 12093 96.1 1.269
-06.0 93 73.88 2862 3274 51749 12222 96.6 1.249
-05.0 94 74.67 2893 3346 53489 12348 96.9 1.230
-04.0 95 75.46 2925 3418 55289 12468 97.3 1.212 ! Near Maximum !
-03.0 96 76.24 2956 3492 57152 12585 97.7 1.193 ! Near Maximum !
-02.0 97 77.03 2987 3565 59080 12696 98.0 1.175 ! Near Maximum !
-01.0 98 77.81 3018 3640 61077 12803 98.3 1.157 ! Near Maximum !
+00.0 99 78.60 3049 3715 63146 12905 98.6 1.140 ! Near Maximum !
+01.0 100 79.39 3080 3791 65289 13001 98.8 1.123 !DANGEROUS LOAD-DO NOT USE!
+02.0 101 80.17 3111 3868 67509 13092 99.1 1.106 !DANGEROUS LOAD-DO NOT USE!
+03.0 102 80.96 3142 3946 69811 13178 99.3 1.089 !DANGEROUS LOAD-DO NOT USE!
+04.0 103 81.74 3173 4024 72198 13258 99.4 1.073 !DANGEROUS LOAD-DO NOT USE!
+05.0 104 82.53 3204 4102 74673 13332 99.6 1.057 !DANGEROUS LOAD-DO NOT USE!
Results caused by ± 10% powder lot-to-lot burning rate variation using nominal charge
Data for burning rate increased by 10% relative to nominal value:
+Ba 99 78.60 3184 4053 74923 12638 100.0 1.059 !DANGEROUS LOAD-DO NOT USE!
Data for burning rate decreased by 10% relative to nominal value:
-Ba 99 78.60 2865 3281 51634 12527 93.0 1.245
mjcmichigan
Handloader
- Dec 26, 2016
- 2,358
- 259
AnthonyC":qfm789fa said:
Hi Anthony,
I used IMR 4350 and was just under 3000 fps with AccuBond.
OAL that worked for my 300WM is written on the target. ABs like Jump
Sent from my iPhone using Tapatalk
AnthonyC":2c7nw8wb said:
Not sure what to give you as far as advice and what powders are available to you, but a couple 300's I have ran did anywhere from 3000-3100 (H4831SC, RL22, IMR7828SSC, RL25) with most of the Nosler 180's. My OLD elk hunting partner uses H4350 and his accuracy in an old beat up Model 70 is usually outstanding, even running 50 year old Partitions or whatever he has squirreled away on the shelf. I wouldn't be concerned if the load ran 2950 or 3050 as long as it was accurate. If you have Retumbo it may be worth a shot as well.
If you aren't getting the accuracy you think you want start moving that AccuBond away from the rifling, I'd probably try .020" at a spell, usually something will jump out at you. Some have luck close up, I have not though.
mjcmichigan
Handloader
- Dec 26, 2016
- 2,358
- 259
AnthonyC":2h80dwn6 said:
I suppose one more thing,
Have you gotten any weight bullet to shoot well? If not, might be time to look at the screw length on you scope mounts. If you have one thread too many, your scope position can vary shot to shot and make clover leaf look like a 2” group.
Sent from my iPhone using Tapatalk
Building a 338 RUM load for a hunting buddy. Starting components as follows.
250 grain Barnes LRX
New Remington brass
O.A.L. will be set at maximum
26" Barrel
Federal 215 primer
I'm thinking of starting with Allients Reloder 33, but I'd like a look at the other useful powders & estimated speeds please.
Anyone?
250 grain Barnes LRX
New Remington brass
O.A.L. will be set at maximum
26" Barrel
Federal 215 primer
I'm thinking of starting with Allients Reloder 33, but I'd like a look at the other useful powders & estimated speeds please.
Anyone?
Anthony,
I'd try to figure max out and start 2-3 gr under and step one load every .2 to .3 gr if you have a MagnetoSpeed? If so, do that and find a flat spot. Use the middle of the flat spot and you should be happy.
http://www.65guys.com/10-round-load-development-ladder-test/
I'd try to figure max out and start 2-3 gr under and step one load every .2 to .3 gr if you have a MagnetoSpeed? If so, do that and find a flat spot. Use the middle of the flat spot and you should be happy.
http://www.65guys.com/10-round-load-development-ladder-test/
There's no 250 LRX, its a 265 so I ran that
Code:
Cartridge : .338 Rem Ultra Mag
Bullet : .338, 265, Barnes 'LRX' BT 30434
Useable Case Capaci: 89.240 grain H2O = 5.794 cm³
Cartridge O.A.L. L6: 3.600 inch = 91.44 mm
Barrel Length : 26.0 inch = 660.4 mm
Predicted Data for Indicated Charges of the Following Powders.
Matching Maximum Pressure: 62000 psi, or 427 MPa
or a maximum loading ratio or filling of 110 %
These calculations refer to your specified settings in QuickLOAD 'Cartridge Dimensions' window.
C A U T I O N : any load listed can result in a powder charge that falls below minimum suggested
loads or exceeds maximum suggested loads as presented in current handloading manuals. Understand
that all of the listed powders can be unsuitable for the given combination of cartridge, bullet
and gun. Actual load order can vary, depending upon lot-to-lot powder and component variations.
USE ONLY FOR COMPARISON !
30 loads produced a Loading Ratio below user-defined minimum of 90%. These powders have been skipped.
Powder type Filling/Loading Ratio Charge Charge Vel. Prop.Burnt P max P muzz B_Time
% Grains Gramm fps % psi psi ms
--------------------------------- -----------------------------------------------------------------
ADI AR 2218 110.0 96.4 6.25 2859 98.7 62000 12314 1.317 ! Near Maximum !
Vihtavuori N570 106.3 92.2 5.97 2848 98.5 62000 12060 1.339 ! Near Maximum !
ReloadSwiss RS 80 109.4 97.6 6.32 2842 99.2 62000 11864 1.335 ! Near Maximum !
Alliant Reloder-33 108.0 96.4 6.25 2836 98.7 62000 11923 1.340 ! Near Maximum !
Hodgdon Retumbo 110.0 91.0 5.90 2811 100.0 61969 10456 1.334 ! Near Maximum !
ADI AR 2225 110.0 91.0 5.90 2811 100.0 61969 10456 1.334 ! Near Maximum !
Norma MRP 2 105.2 86.5 5.61 2781 100.0 62000 10695 1.358 ! Near Maximum !
Bofors RP30 105.2 86.5 5.61 2781 100.0 62000 10695 1.358 ! Near Maximum !
PB Clermont PCL 517 100.2 88.0 5.70 2780 100.0 62000 10512 1.341 ! Near Maximum !
SNPE Vectan SP 12 100.0 87.8 5.69 2778 100.0 62000 10485 1.342 ! Near Maximum !
Alliant Reloder-26 94.2 83.3 5.40 2778 100.0 62000 10134 1.363 ! Near Maximum !
Vihtavuori N560 97.2 81.7 5.29 2777 99.8 62000 10770 1.349 ! Near Maximum !
Accurate MAGPRO 97.5 85.2 5.52 2772 99.3 62000 10925 1.356 ! Near Maximum !
Norma MRP 95.3 81.8 5.30 2769 100.0 62000 10295 1.356 ! Near Maximum !
Alliant Reloder-25 103.1 84.3 5.46 2767 100.0 62000 9903 1.345 ! Near Maximum !
IMR 7828 SSC 96.2 81.3 5.27 2767 100.0 62000 10387 1.338 ! Near Maximum !
IMR 7828 101.7 81.3 5.27 2767 100.0 62000 10387 1.338 ! Near Maximum !
ReloadSwiss RS 70 92.7 81.3 5.26 2764 100.0 62000 9992 1.340 ! Near Maximum !
ADI AR 2213 97.3 80.9 5.24 2756 99.9 62000 10347 1.336 ! Near Maximum !
ADI AP 2214 101.2 86.4 5.60 2756 100.0 62000 10167 1.332 ! Near Maximum !
Hodgdon H1000 106.4 86.6 5.61 2754 100.0 62000 10138 1.332 ! Near Maximum !
ADI AR 2217 106.4 86.6 5.61 2754 100.0 62000 10138 1.332 ! Near Maximum !
Norma 217 110.0 89.1 5.77 2752 100.0 56654 10675 1.407 ! Near Maximum !
Hodgdon H870 110.0 93.4 6.05 2751 98.9 56422 11450 1.401 ! Near Maximum !
Alliant Reloder-22 97.4 81.0 5.25 2749 100.0 62000 10233 1.356 ! Near Maximum !
Bofors RP5/NP ~approximation 97.4 81.0 5.25 2749 100.0 62000 10233 1.356 ! Near Maximum !
Raufoss RA15 97.4 81.0 5.25 2749 100.0 62000 10233 1.356 ! Near Maximum !
Bofors RP15 100.1 81.4 5.28 2748 100.0 62000 10257 1.357 ! Near Maximum !
Winchester WXR 100.1 81.4 5.28 2748 100.0 62000 10257 1.357 ! Near Maximum !
Alliant Reloder-50 110.0 97.9 6.34 2748 97.3 55759 11949 1.429 ! Near Maximum !
Vihtavuori 24N41 108.7 95.2 6.17 2737 93.5 62000 11026 1.339 ! Near Maximum !
Bofors RP5 NT ~approximation 101.0 84.7 5.49 2732 99.2 62000 10377 1.339 ! Near Maximum !
Ramshot Magnum 97.4 87.3 5.66 2729 100.0 62000 9729 1.353 ! Near Maximum !
Rottweil R905 98.8 80.7 5.23 2724 99.8 62000 10122 1.357 ! Near Maximum !
ADI AR 2209 94.2 77.1 4.99 2713 100.0 62000 9748 1.345 ! Near Maximum !
Alliant Reloder-19 94.7 77.9 5.05 2711 100.0 62000 9796 1.353 ! Near Maximum !
Bofors RP14 ~approximation 95.4 78.5 5.08 2705 100.0 62000 9730 1.354 ! Near Maximum !
PB Clermont PCL 518 91.0 77.3 5.01 2699 100.0 62000 9450 1.361 ! Near Maximum !
Alliant Reloder-23 99.5 80.1 5.19 2697 100.0 62000 9162 1.370 ! Near Maximum !
Hodgdon H4831 SC 96.0 79.9 5.18 2695 99.7 62000 9823 1.351 ! Near Maximum !
Hodgdon H4831 99.9 79.9 5.18 2695 99.7 62000 9823 1.351 ! Near Maximum !
Ramshot Hunter 90.3 76.7 4.97 2694 100.0 62000 9365 1.362 ! Near Maximum !
Raufoss RA4 92.9 76.4 4.95 2691 100.0 62000 9575 1.354 ! Near Maximum !
Bofors RP4 ~approximation 92.9 76.4 4.95 2691 100.0 62000 9575 1.354 ! Near Maximum !
Vihtavuori N170 109.2 88.8 5.76 2690 97.0 62000 10325 1.372 ! Near Maximum !
Alliant Reloder-16 91.4 73.3 4.75 2681 100.0 62000 8951 1.370 ! Near Maximum !
Bofors 12,7mmRA NC1214 Lot20115087 110.0 95.7 6.20 2672 90.1 56767 11384 1.446 ! Near Maximum !
Somchem S385 94.8 78.8 5.11 2672 100.0 62000 9279 1.376 ! Near Maximum !
Winchester Supreme 780 93.6 81.2 5.26 2668 100.0 62000 9338 1.362 ! Near Maximum !
Rottweil R904 93.9 76.1 4.93 2668 99.9 62000 9424 1.355 ! Near Maximum !
Lovex D100 106.1 93.9 6.09 2666 94.0 62000 10165 1.362 ! Near Maximum !
IMR 4955 Enduron 97.4 78.0 5.05 2665 99.7 62000 9544 1.354 ! Near Maximum !
Bofors RP4 NT ~approximation 90.6 75.7 4.90 2662 100.0 62000 9128 1.369 ! Near Maximum !
Somchem S365 91.2 74.6 4.84 2660 100.0 62000 8657 1.380 ! Near Maximum !
Vihtavuori N165 99.9 81.3 5.27 2659 100.0 62000 9092 1.367 ! Near Maximum !
Vihtavuori N160 100.2 79.0 5.12 2653 99.9 62000 9255 1.360 ! Near Maximum !
Lovex S071 103.1 80.2 5.19 2651 100.0 62000 8948 1.395 ! Near Maximum !
Accurate 3100 97.5 80.2 5.19 2651 100.0 62000 8948 1.395 ! Near Maximum !
IMR 4831 94.2 74.2 4.81 2649 100.0 62000 8752 1.381 ! Near Maximum !
Somchem S361 93.0 81.5 5.28 2643 99.7 62000 9302 1.368 ! Near Maximum !
Hodgdon Hybrid 100V 92.2 73.3 4.75 2621 100.0 62000 8257 1.375 ! Near Maximum !
IMR 7977 Enduron 102.0 83.0 5.38 2620 95.2 62000 9475 1.358 ! Near Maximum !
Hodgdon US 869 110.0 96.4 6.25 2612 91.3 53503 10644 1.442
Hodgdon 50BMG 110.0 91.9 5.95 2608 87.2 53386 10734 1.442
SNPE Vectan SP 13 110.0 92.5 5.99 2562 95.0 49515 10323 1.496
Accurate 8700 110.0 94.4 6.12 2554 94.8 48405 10352 1.492
Somchem 12.7-0 110.0 93.4 6.05 2552 86.7 53526 9925 1.442
Vihtavuori 20N29 110.0 97.4 6.31 2544 92.2 47564 10565 1.513
PB Clermont PCL 513/520/9520 110.0 92.5 5.99 2508 92.8 46434 10186 1.532
NC A3502 ,test only 110.0 88.5 5.74 2317 70.6 41186 8683 1.597
TLP A 502(RH) ,test only 110.0 88.5 5.74 2288 74.0 39115 8828 1.632
V1734 7-multiperf ,test only 110.0 88.5 5.74 1659 35.5 21888 4357 2.150
andrewctillman
Beginner
- Feb 6, 2013
- 225
- 1
Can you run the following for me?
IMR4895, Winchester brass, 308 Winchester, 20 inch barrel, 178 grain HORNADY ELD-X, 2.860 OCL.
Not ideal but I've been using up old lots of powder in my Rem 40X. Gone thhrough RL15, Varget, 4064, and VV550 cans and now left w 4 pounds of 4895!
PS, I was surprised to see 4895 had such a high flame temperature on QL.
IMR4895, Winchester brass, 308 Winchester, 20 inch barrel, 178 grain HORNADY ELD-X, 2.860 OCL.
Not ideal but I've been using up old lots of powder in my Rem 40X. Gone thhrough RL15, Varget, 4064, and VV550 cans and now left w 4 pounds of 4895!
PS, I was surprised to see 4895 had such a high flame temperature on QL.
DrMike
Ballistician
- Nov 8, 2006
- 37,041
- 5,355
Code:
Cartridge : .308 Win. (SAAMI)
Bullet : .308, 178, Hornady ELD-X 3074 G7
Useable Case Capaci: 44.753 grain H2O = 2.906 cm³
Cartridge O.A.L. L6: 2.800 inch = 71.12 mm
Barrel Length : 20.0 inch = 508.0 mm
Powder : IMR 4895
Predicted data by increasing and decreasing the given charge,
incremented in steps of 1.0% of nominal charge.
CAUTION: Figures exceed maximum and minimum recommended loads !
Step Fill. Charge Vel. Energy Pmax Pmuz Prop.Burnt B_Time
% % Grains fps ft.lbs psi psi % ms
-10.0 93 38.52 2350 2182 44271 8349 95.9 1.205
-09.0 94 38.95 2375 2230 45728 8441 96.3 1.187
-08.0 95 39.38 2401 2278 47234 8530 96.7 1.170
-07.0 96 39.80 2427 2327 48789 8616 97.0 1.152
-06.0 98 40.23 2452 2376 50398 8700 97.4 1.136
-05.0 99 40.66 2477 2426 52060 8781 97.7 1.119
-04.0 100 41.09 2503 2476 53780 8858 98.0 1.103 ! Near Maximum !
-03.0 101 41.52 2528 2526 55558 8933 98.2 1.087 ! Near Maximum !
-02.0 102 41.94 2554 2577 57397 9005 98.5 1.071 ! Near Maximum !
-01.0 103 42.37 2579 2629 59300 9074 98.7 1.056 ! Near Maximum !
+00.0 104 42.80 2604 2681 61269 9139 98.9 1.041 ! Near Maximum !
+01.0 105 43.23 2629 2733 63307 9200 99.1 1.026 !DANGEROUS LOAD-DO NOT USE!
+02.0 106 43.66 2655 2785 65418 9259 99.3 1.011 !DANGEROUS LOAD-DO NOT USE!
+03.0 107 44.08 2680 2838 67604 9314 99.5 0.997 !DANGEROUS LOAD-DO NOT USE!
+04.0 108 44.51 2705 2892 69869 9365 99.6 0.983 !DANGEROUS LOAD-DO NOT USE!
+05.0 109 44.94 2730 2945 72216 9412 99.7 0.969 !DANGEROUS LOAD-DO NOT USE!
Results caused by ± 10% powder lot-to-lot burning rate variation using nominal charge
Data for burning rate increased by 10% relative to nominal value:
+Ba 104 42.80 2714 2912 73380 8840 100.0 0.967 !DANGEROUS LOAD-DO NOT USE!
Data for burning rate decreased by 10% relative to nominal value:
-Ba 104 42.80 2451 2373 49582 8990 93.8 1.138andrewctillman
Beginner
- Feb 6, 2013
- 225
- 1
Thanks!
(Might have to switch back to a 168).
(Might have to switch back to a 168).
